Adafruit Trinket – 5V Logic ADA1501 – Mini Microcontroller



Adafruit 100232 - Up to 16v input, reverse-polarity protection, thermal and current-limit protection. Perfect for when you don't want to give up your expensive dev-board and you aren't willing to take apart the project you worked so hard to design. This is the 5V Trinket. We designed a usb bootloader so you can plug it into any computer and reprogram it over a USB port just like an Arduino.

We wanted to design a microcontroller board that was small enough to fit into any project, and low cost enough to use without hesitation. There are two versions of the Trinket. The 3v version should only run at 8 MHz. You can't stack a big shield on it but for many small & simple projects the Trinket will be your go-to platform.

Adafruit Trinket - 5V Logic ADA1501 - Mini Microcontroller - Simply use a usb v2 port or a usb hub in between attiny85 on-board, 512 byte of SRAM, 512 bytes of eeprom internal oscillator runs at 8MHz, 8k of flash, but can be doubled in software for 16MHz. Usb bootloader with a nice led indicator looks just like a USBtinyISP so you can program it with AVRdude with a simple config modification and/or the Arduino IDE with a few simple config modifications.

Use the 3v one to interface with sensors and devices that need 3V logic, or when you want to power it off of a LiPo battery. Use the 5v one for sensors and components that can use or require 5V logic. On-board 5. 0v power regulator with 150ma output capability and ultra-low dropout.

More information about Adafruit 100232

Adafruit 24 RGB LED Neopixel Ring


Adafruit 100226 - In stock & Ready to Ship. Use only one microcontroller pin to control as many as you can chain together! Each LED is addressable as the driver chip is inside the LED. Adafruit part Number: 1586. The rings are 'chainable' - connect the output pin of one to the input pin of another. Round and round and round they go! 24 ultra bright smart LED NeoPixels are arranged in a circle with 2.

6" 66mm outer diameter. Does not include any other accessories. Each one has ~18ma constant current drive so the color will be very consistent even if the voltage varies, and no external choke resistors are required making the design slim. Note: includes circuit board only. Power the whole thing with 5VDC and you're ready to rock.

Adafruit 24 RGB LED Neopixel Ring - Stock type: NeoPixels >> Rings.

More information about Adafruit 100226


Similar products



Adafruit Pro Trinket 5V 16MHz 1 Piece


Adafruit FBA_2000 - The bootloader does not affect RAM usage. Atmega328p onboad chip in QFN package. At the same speed and voltage. Trinket's a year old now, and while its been great to see tons of tiny projects, more FLASH, sometimes you just need more pins, and more RAM. Like the trinket, it has onboard USB bootloading support - we opted for a MicroUSB jack this time.

So you'll be happy to hear that not only is pro trinket programmable using the arduino ide as you already set up, but 99% of arduino projects will work out of the box! Here's some things you may have to consider when adapting Arduino sketches: Pins #2 and #7 are not available they are exclusively for USB The onboard 5V regulator can provide 150mA output, not 800mA out You cannot plug shields directly into the Pro Trinket There is no Serial-to-USB chip onboard.

Adafruit Pro Trinket 5V 16MHz 1 Piece - Micro-usb jack for power and/or usb uploading, reverse-polarity protection, you can put it in a box or tape it up and use any USB cable for when you want to reprogram. Adafruit part Number: 1586. We also added optiboot support, so you can either program your Pro Trinket over USB or with a FTDI cable just like the Pro Mini and friends.

In stock & Ready to Ship. The pro trinket PCB measures only 1. 5" x 07" x 02" without headers but packs much of the same capability as an Arduino UNO.

More information about Adafruit FBA_2000


Similar products



12 x 5050 RGB LED with Integrated Drivers ADA1643 - Adafruit NeoPixel Ring


Adafruit 100358 - Micro-usb jack for power and/or usb uploading, reverse-polarity protection, you can put it in a box or tape it up and use any USB cable for when you want to reprogram. In stock & Ready to Ship. In stock & Ready to Ship. Our wonderfully-written neopixel library for Arduino supports these pixels! As it requires hand-tuned assembly it is only for AVR cores but others may have ported this chip driver code so please google around.

Round and round and round they go! 12 ultra bright smart LED NeoPixels are arranged in a circle with 1. 5" 37mm outer diameter. Use only one microcontroller pin to control as many as you can chain together! Each LED is addressable as the driver chip is inside the LED. Each one has ~18ma constant current drive so the color will be very consistent even if the voltage varies, and no external choke resistors are required making the design slim.

12 x 5050 RGB LED with Integrated Drivers ADA1643 - Adafruit NeoPixel Ring - An 8mhz or faster processor is required. Comes as a single ring with 12 individually addressable RGB LEDs assembled and tested. Neopixel ring - 12 x 5050 rgb led with integrated Drivers 3:40 Adafruit part Number: 1586. On-board 5. 0v power regulator with 150mA output capability and ultra-low dropout. Usb bootloader with a nice led indicator looks just like a USBtinyISP so you can program it with AVRdude and/or the Arduino IDE with a few simple config modifications.

More information about Adafruit 100358


Similar products



Mini Microcontroller - 3.3V Logic ADA1500 - Adafruit Trinket


Adafruit 100364 - We wanted to design a microcontroller board that was small enough to fit into any project, and low cost enough to use without hesitation. Use the 5v one for sensors and components that can use or require 5V logic. In stock & Ready to Ship. The 3v version should only run at 8 MHz. Trinket may be small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATtiny85, a little chip with a lot of power.

Perfect for when you don't want to give up your expensive dev-board and you aren't willing to take apart the project you worked so hard to design. 16mhz clock rate, 28K FLASH available. We designed a usb bootloader so you can plug it into any computer and reprogram it over a USB port just like an Arduino.

Usb bootloader with a nice led indicator looks just like a USBtinyISP so you can program it with AVRdude and/or the Arduino IDE with a few simple config modifications. Also has headers for an FTDI port for reprogramming. Stock type: NeoPixels >> Rings. It's our lowest-cost arduino-iDE programmable board! As of May 27th, 2015 the 3.

Mini Microcontroller - 3.3V Logic ADA1500 - Adafruit Trinket - 3v trinket has been revised!  the board is now even smaller - at just 27mm x 15mm - and comes with a micro-B USB connector rather than mini-BThe Attiny85 is a fun processor because despite being so small, and 5 I/O pins, it has 8K of flash, including analog inputs and PWM 'analog' outputs. Attiny85 on-board, 512 byte of sram, 8k of flash, 512 bytes of EEPROM.

More information about Adafruit 100364


Similar products



Adafruit NeoPixel Jewel - 7 x WS2812 5050 RGB LED with Integrated Drivers ADA2226 Original Version


Adafruit 2226 - Stock type: NeoPixels >> Boards. Micro-usb jack for power and/or usb uploading, reverse-polarity protection, you can put it in a box or tape it up and use any USB cable for when you want to reprogram. Internal oscillator runs at 8MHz, but can be doubled in software for 16MHz. Our wonderfully-written neopixel library for Arduino supports these pixels! As it requires hand-tuned assembly it is only for AVR cores but others may have ported this chip driver code so please google around.

Adafruit NeoPixel Jewel - 7 x WS2812 5050 RGB LED with Integrated Drivers ADA2226 Original Version - Stock type: NeoPixels >> Rings. In stock & Ready to Ship. Power the whole thing with 5VDC and you're ready to rock. The leds are 'chainable' by connecting the output of one Jewel into the input of another. On-board 5. 0v power regulator with 150mA output capability and ultra-low dropout. An 8mhz or faster processor is required.

Comes as a single round board with 7 individually addressable RGB LEDs assembled and tested. Adafruit part Number: 2226. Stock type: NeoPixels >> Rings. Adafruit part Number: 1500 There is a single data line with a very timing-specific protocol.

More information about Adafruit 2226


Similar products



Adafruit Metro Mini 328-5V 16MHz


Adafruit 2590 - Micro-usb jack for power and/or usb uploading, reverse-polarity protection, you can put it in a box or tape it up and use any USB cable for when you want to reprogram. Usb bootloader with a nice led indicator looks just like a USBtinyISP so you can program it with AVRdude and/or the Arduino IDE with a few simple config modifications.

Also has headers for an FTDI port for reprogramming. When we need to go small, we use a pro trinket 3v or 5v, but if you want to have USB-to-Serial built in, we reach for an Adafruit METRO Mini . Metro mini is the culmination of years of playing with AVRs: we wanted to make a tiny, breadboard-friendly development board that is easy to use and is hacker friendly.

Adafruit Metro Mini 328-5V 16MHz - Internal oscillator runs at 8MHz, but can be doubled in software for 16MHz. There's also 6 pwms available on 3 timers 1 x 16-bit, hardware I2C port and hardware UART to USB. Gpio logic level is 5v but by cutting and soldering closed a jumper on the bottom, you can easily convert it to 3. 3v logic. On-board 5.

0v power regulator with 150mA output capability and ultra-low dropout. Atmega328p onboad chip in QFN package. Stock type: NeoPixels >> Rings.

More information about Adafruit 2590


Similar products



ALITOVE 100pcs WS2812B Addressable 5050 smart RGB LED Pixel light on Black Heat Sink PCB Board for Arduino 5V DC


ALITOVE 4334419429 - Atmega328p onboad chip in QFN package. So you need to solder them based on your requirement. You can set to any color or animation. It's put on a small pcb board that allows you to solder it in whatever configuration you want. It's easy to wire up and control. Stock type: NeoPixels >> Boards. Usb to serial converter, there's a genuine ftdi hardware usB to Serial converter that can be used by any computer to listen/send data to the METRO, and can also be used to launch and update code via the bootloader.

Internal oscillator runs at 8MHz, but can be doubled in software for 16MHz. The chainable design means no crossed threads. Works great with adafruit neopixel library, arduino due & arduino mega/ADK, ready-to-go library & example code for the Arduino UNO/Duemilanove/Diecimila, Flora/Micro/Leonardo, Trinket/Gemma, FastLED library and Raspberry Pi.

ALITOVE 100pcs WS2812B Addressable 5050 smart RGB LED Pixel light on Black Heat Sink PCB Board for Arduino 5V DC - It works almost the same as NeoPixel and has superior quality but it is much cheaper than NeoPixel. Stock type: NeoPixels >> Rings. Power the metro mini with 6-16v polarity protected on the Vin pin, or plug the micro USB connector to any 5V USB source. 20 gpio pins, 6 of which are analog in as well, 2 x 8-bit.

Adafruit part Number: 2226. In stock & Ready to Ship.

More information about ALITOVE 4334419429


Similar products



Kuman 100pcs WS2812B 5050 Addressable SMD Smart rgb led Strip Great Pixel LED lights for Arduino 5V DC Single 1-led LED Module Pixels Color Light littlergb LEDs Lampon Black Heat Sink PCB Board


Kuman WS2812B-US - Model: ws2812 pixel board light source: smd 5050 rgb ic model: ws2812B the gray level: 256 Beam angle: 120 ° Power: 03w ± 001% fpcb board color: black color:full color, can be adjusted by the controller as follows: white, yellow, blue, green, red, etc. Micro-usb jack for power and/or usb uploading, reverse-polarity protection, you can put it in a box or tape it up and use any USB cable for when you want to reprogram.

Awesome price for the leds. Stock type: NeoPixels >> Rings. There are no traces connecting the modules It works almost the same as NeoPixel and has superior quality. Adafruit part Number: 2226. Adafruit part Number: 1500 In stock & Ready to Ship. Soldering can be challenging because of the size but also because these little guys can burn out if the soldering tip is left on the contact too long.

Kuman 100pcs WS2812B 5050 Addressable SMD Smart rgb led Strip Great Pixel LED lights for Arduino 5V DC Single 1-led LED Module Pixels Color Light littlergb LEDs Lampon Black Heat Sink PCB Board - Arduino is not included. The ultra bright ws2812b smart full-color led pixel is individually addressable. If you want to save money, the product will be your choice. Up to 16v input, thermal and current-limit protection. Adafruit part Number: 1643.

More information about Kuman WS2812B-US


Similar products



Adafruit NeoPixel Stick for Arduino- 8 x WS2812 5050 RGB LED with Integrated Drivers


Adafruit Industries 1426-fba-FBACA - The litlle rgb led is easy to program, because the addressable IC is built-in the 5050SMD and it makes this led module to light up each individual 5050SMD at your wish. An 8mhz or faster processor is required. In stock & Ready to Ship. You just need one digital pin plus 5V and ground to control as many LEDs.

There is a single data line with a very timing-specific protocol. Stock type: NeoPixels >> Rings. In stock & Ready to Ship. 16mhz clock rate, 28K FLASH available. Adafruit part Number: 1586. Power the metro mini with 6-16v polarity protected on the Vin pin, or plug the micro USB connector to any 5V USB source. 20 gpio pins, 6 of which are analog in as well, 2 x 8-bit.

Adafruit NeoPixel Stick for Arduino- 8 x WS2812 5050 RGB LED with Integrated Drivers - Up to 16v input, thermal and current-limit protection. Adafruit part Number: 1643. Easy to solder leads onto the pre-tinned pads,Have any other components need pre-soldered to the boards,put on a small PCB board that allows you to solder it in whatever configuration you want. It cannot be used with a Linux-based microcomputer or interpreted microcontroller such as the netduino or Basic Stamp.

Use only one microcontroller pin to control as many as you can chain together! Each LED is addressable as the driver chip is inside the LED. Atmega328 brains - this popular chip has 32kb of flash 1/2 K is reserved for the bootloader, 2KB of RAM, clocked at 16MHz.

More information about Adafruit Industries 1426-fba-FBACA


Similar products



v1 ADA1904 - USB LiIon/LiPoly charger - Adafruit Micro Lipo w/MicroUSB Jack


Adafruit 1904 - Stock type: NeoPixels >> Boards. Easy to solder leads onto the pre-tinned pads,Have any other components need pre-soldered to the boards,put on a small PCB board that allows you to solder it in whatever configuration you want. It has 256 brightness display and full 24-bit 16, 777, 216 color display. Compact size, but did we mention they are bright!

v1 ADA1904 - USB LiIon/LiPoly charger - Adafruit Micro Lipo w/MicroUSB Jack - Battery not included. Stock type: NeoPixels >> Rings. Adafruit part Number: 1586. Very bright great little pixels for projects. There's a hardware spi port, and 2 of which are reserved for the USB-serial converter. Atmega328p onboad chip in QFN package. You can set to any color or animation. It's put on a small pcb board that allows you to solder it in whatever configuration you want.

It's easy to wire up and control. In stock & Ready to Ship. Adafruit micro lipo w/microusb jack - usb liIon/LiPoly charger - v1 Adafruit Product ID: 1904. Atmega328 brains - this popular chip has 32kb of flash 1/2 K is reserved for the bootloader, 2KB of RAM, clocked at 16MHz. A fun and easy Arduino project.

More information about Adafruit 1904


Similar products